Coatesville, PA

.

Performed heat pump tuneup on a 2022 Payne heat pump. Check electrical components, low and high voltage connections ok filter 20x20x1 ok. Flush drain test water safeties ok ez trap and wet switch ok check airflow supply and return ok outdoor unit refrigerant test 7.5 kw back up heat ok.

Perform precision heat tuneup on eight propane high-efficiency gas furnaces. Replaced all air filters that were applicable. Clean flame sensors. Tested lower capacitors. Check gas pressures. Check temperature rise. Inspected burners. Performed combustion test. Found after closer examination with camera that hallway, propane, furnace had a cracked heat exchanger And a broken in-line drain assembly. This furnace is from 2002 Frigidaire recommend replacing gas furnace. Our office to call to set up A time to have someone come out to give a replacement estimate. Seven gas furnaces are working at time of service. Also provide estimate to replace inducer motor for auditorium right side.

Completed heat tune up for hybrid 3 ton heat pump 80,000 BTU furnace Filter in good condition Inspected heat exchanger, burners, inducer assembly, pressure switches Cleaned flame sensor, verified flame rectification circuit Ignitor in good condition, measured ohm reading Confirmed 1st and second stage manifold gas pressure Cleared ez trap, inspected drain and pump, added treatment tabs Measured temperature rise and static pressure, checked fan speeds. Combustion and draft tests: Pass Verified Heat pump operation and temperature rise. Homeowner became plan member for system today.

Completed heat tune up for 2 ton heat pump (7.2KW electric heat backup) Replaced 14x20x1 filter. Indoor and outdoor coils in good condition. Inspected drain and pump. There are no water safeties. Trap is also not serviceable/cannot clean out. Left estimate for EZ trap, wet switch and to wire in condensate pump safety, Inspected wiring, controls, electric motors and components. 16A for 7.5KW electric heat kit: The amp draw should be around 30A one of the elements is burned out. I called Pierce Phelps it is under warranty. Left estimate for labor only charge to replace electric heat kit. does not have an input for outdoor temperature and heat pump droop was set to comfort, therefore electric heat always energizes on call for heat. I changed the droop to 2° at thermostat today, A WiFi thermostat would allow for locking out of electric heat based on outdoor temperature. Left estimates. There is no surge protection on equipment. Left email estimates. Refrigerant pressures and diagnosti

Completed plan member heat tune up 100,000 BTU natural gas furnace: Replaced 16x25x1 filter Inspected burner, heat exchanger, inducer assembly Ignitor in good condition, measured ohm value Cleaned flame sensor, verified flame rectification circuit Confirmed manifold gas pressures Cleared EZ trap, inspected drains Measured temperature rise and static pressure Combustion and draft tests: Pass. Furnace operating well at this time. There is a section of 3/4” copper piping on water heater hot line that is very corroded. Left an estimate to drain water heater as necessary and replace this section of the piping. The ST 5 expansion tank has failed. Left estimate to replace The water pressure measured at tank drain is 100+ psi. The domestic water pressure reducing valve has failed. Left estimate to replace. Household is 3 adults. The other consideration is that the water heater is 11 years old. Left 3 estimates for electric water heaters. VERY IMPORTANT: If water heater is replaced tha

Estimate.

Thoroughly cleaned evaporator coil inside and out and sprayed down all the u bends on the coil. Also sprayed and wipe down evaporator drain pan. Ran system and AC mode for about 30 minutes and let condense to see if returns. Also got homeowner to smell at the vents. After kicking heat pump heat back on cold smell the dirty sock smell at initial start up. Called trane tech support. Trane recommended using bio fresh cleaner after thoroughly cleaning evaporator coil. Will go over info with our office.

Heat tune up 60,000 BTU natural gas furnace. Homeowner recently replaced 20x25x1 filter. I left additional there. Homeowner also replaced housing and Aprilaire 45 water panel. Tested operations of humidifier. Set humidistat to 35%, bypass damper is open. Inspected burners heat exchanger, inducer assembly, pressure switches Ignitor in good condition, verified ohm reading. Cleaned flame sensor, verified flame rectification circuit Confirmed manifold natural gas pressure (3.5”) Inspected wiring, controls, electric motors and components; there is no surge protectors I left email estimates: one estimate is for the 120V circuit, the other for the blower motor only; also left estimate for surge protector for outdoor equipment circuit Measured temperature rise and static pressure Combustion and draft tests: Pass System operating well at this time.

Performed a QA on a heat pump system. Took photos of the equipment and looked at the overall install of the indoor unit and the outdoor heat pump. Looked at the wiring connections and the voltages. Inspected the drain lines and tested . Inspected the air filter. Looked at temp splits for the system . Outside unit checked the disconnect and the outdoor unit level and made sure all connections are sealed and wiring was completed in a neatly fashion. Refrigerant Charge was good and checked compressor and fan amp draws. New equipment is working fine at this time of service

Performed six month inspection on a recently installed system test operation of gas furnace low and high stage. Check airflow supply return air change air filter. Check train link thermostat settings test regular heat from the heat pump recycle unit couple times ok. This is first winter customer has heat pump outside unit will come on during winter. Show customer how to activate gas furnace only an override thermostat settings. Just in case customer wants to use gas furnace only not the heat pump heating side.

No heat gas boiler. No operation from boiler. Checked operation of boiler, found no low voltage to boiler, checked all wiring and components, found fan center transformer open and not feeding power open primary. Provided estimate to replace fan center and test operation customer approved repairs after install of fan center test operation of boiler cycle. Couple times performed combustion test check draft. Ok water pressure and temp ok. Would recommend service plan on boiler. Flue damper is on the open manually setting. Customer signed up for gas boiler service plan. Office to follow up customer to schedule tune up.

Performed gas heat tune up 80 k btu furnace American standard. Check electrical low and high ok air filter ok. Clean sensor and inspect burners ok performed combustion test check supply and return air 65 degrees temperature rise. safety test on heat exchanger failed. Used camera to inspect heat exchanger and found crack on heat exchanger. Informed customer about this issue due to safety concern, furnace should not be on operation until repairs are done. Went over with customer on safety protocol red red tag procedure and provided options on repairs. Other option is to upgrade heater. Customer is responsible from now on if they want to continue running furnace under these conditions. Office to follow up with customer..

Performed tuneup on 5 yr old amana gas furnace, tested combustion for the unit and gas pressure as well as checked and tested all related ignition components. Cleaned and tested flame sensor checked burners and heat exchanger as well as blower motor amperage and inducer motor amperage clean and flush drains as well. No issues with unit at this time.

Upon arrival for maintenance on gas furnace I changed air filter. I cleaned the flame sensor. I inspected heat exchanger and burners. I checked blower motor and assembly. I checked the resistance of igniter. Checked all wiring and control board. I checked inducer operation and ensured hose port was clear. I checked gas pressures. Checked air temperature rise. Performed combustion test. Unit is in normal operation at this time.

Issue was carbon monoxide detector going off. Fire dept had been here but homeowners had already aired out the house when they arrived. So fire department told them they couldn’t really check for CO. The CO detector that went off is plugged in within 5 feet of appliances; water heater and furnace. Visual inspection of heat exchanger found a couple of eyelets that are very close to being rusted through. Also a few already at front of heat exchanger where it meets burner compartment that are close to cracking. There is. Total of 100,000 BTUs for the appliances in the closet. So you need 100 sq” of air to the mechanical room. You can cut grilles into doors for this. There is a gap between frame and top of door but not enough. Combustion test for furnace passes and CO levels well within limits. Smoke tests pass. I did the tests with the mechanical room door closed. Also vacuumed and brushed burner compartment there was dirt and lint there. Including on backside of inducer motor whee

Spayed gas fittings with soap bubbles. Very small leak at union to furnace. Tightened. No other leaks found. Tested furnace operations: Ok Furnace appears to have been installed in 2022. Serial number dates to 2021. Replaced 16x20x1 filter. Was very dirty recommend replacing every 2/3 months. Homeowner mentioned that AC was not running. Emergency switch on wall outside mechanical room was off. Tested AC operations. Outdoor coil very dirty. R22 system. Pressures slightly low. Considering age of the equipment, I encouraged homeowner to upgrade AC. He will contact us to set up consultation on Monday. He isn’t sure of exactly when he will be available. Homeowner decided to become AC+Gas Heat plan member. Paid for diagnostic fee and plan membership today.

Reviewed information and created estimate for new Weil Mclain oil boiler and Rheem hot water heater. Emailed proposal.

Completed 6 month inspection for 100,000 BTU natural gas furnace. Replaced 16x25x1 filter. Inspected heat exchanger, burners, inducer assembly Cleaned flame sensor, verified flame rectification circuit Inspected ignitor, reading proper ohms Confirmed proper manifold gas pressures Inspected wiring, controls, electrical motors; heating fan speed set to 1620 CFM in hi fire, 1270 in low fire. 10 minute upstage timer. Measured temperature rise and static pressure Combustion and draft tests: Pass Addressed ductwork issues as well as I could. Identified and marked (2) master bedroom leads, master closet and master bath. I dampened closet and bath almost completely shut and opened bedroom dampers. System operating well at this time.

Estimate

Did a QA on a new trane 2stage gas furnace . Check the cleanliness of all the wires and connections. Inspected the the gas line to check for leaks started the gas furnace and adjusted gas pressure for the first and second stages. Checked the flue piping and checked the drain lines. Checked the control board for proper set up and checked the thermostat for set up. Checked outdoor level and the disconnect level and made sure all penetrations are caulked . Tested the heat pump system operation. Talked with the customer to see if he had any questions. The new system looks good. It’s up and running at this time of service.

Performed tuneup on five year old Goodman gas furnace performed combustion analysis as well as check gas pressures and temperature split across unit. Clean flame sensor as well as all other ignition related components including hot surface igniter and inducer motor, got amp draw off, blower motor and inducer motor customer filter was quite dirty showed and he said he is going to get one later to replace it but is aware he needs another one. Heat exchanger and burner integrity an estimate was created for a protector for the blower motor inside and was emailed to customer and she said she will talk it over with her husband.

Upon arrival for maintenance of gas furnace I changed the filter. I cleaned the flame sensor. Inspected heat exchanger and burners. Blew out drain. Checked blower motor and assembly. Checked uv light operation. Checked control board and all electrical. Checked gas pressure. Checked operation of inducer motor. Checked air ctemperature rise. Performed combustion test. Unit is in normal operation at this time.

Installed new Mitsubishi mini split and outdoor uni. Mounted indoor head and ran new condensate line and communication wiring. Installed new breaker and ran new high volt wire. Installed new disconnect and ran new line set. Cleaned up work area tested out equipment

10/28/2024 Arrived to jobsite to complete testing. Ducts in basement were not sealed and boots were not sealed to the subfloor. Some areas of the home needed to be sealed before completing testing. Contractor to complete additional sealing before tomorrow afternoon so testing can be completed.