Broomall, PA

Perform tuneups on two gas furnaces, check both units and heating mode and tested combustion and gas pressures as well as cleaned and checked flame sensor in hot service igniter. Both units had the temperature split checked as well as the inducer motor and the heat exchanger, blower motors were also inspected and Filters were changed. The circulator pump I own for flushing, tankless hot water heaters was not working so I could not do the flush at this time. Customer was notified and we have to return it another date to do the flush.

Found failed thermocouple. Replaced thermocouple on boiler and tested operation. Boiler is from 2003 explained to customer that a new boiler would be between $10,000 to $14,000. Performed combustion test on boiler and tested both zones. Gas boiler is working fine at time of service.

Returned to site to install new Oil Fill Alarm. Disconnected piping to the original Fill Alarm Whistle. New Fill Whistle was a combination Whistle with a Tank Gauge. Moved to the connection on the tank where the original tank was located and plugged the old Whistle connection. Repiped the section of the Fill pipe and added a Union fitting. Once we had the fill pipe apart found the whistle was completely clogged which caused it to fail. Also found that it was not 1-1/4” pipe but was 1” pipe. Let the homeowner know that in the future it may need to be replaced with a larger fill pipe.

Arrived onsite to take measurements of the Oil Piping to the tank. Fill pipe = 2” Black Iron Vent pipe = 1-1/4” Black Iron x 2” Connection at the tank Took photos and recorded measurements of the piping going to the outside of the home. Oil tank has about 1/4 tank of oil left. They cannot get the oil filled until the whistle is replaced. Let her know we would review the estimate and resend it. She asked if we haven’t already provided service plan pricing if we could add a service plan on to the estimate for them to review. She said they currently do not have anyone servicing the Furnace.

Perform precision gas boiler tuneup on Weil McLain 80% atmosphere gas boiler. Inspected burners inspected top of heat exchanger tested operation of both zone valves. Check gas pressure. Perform combustion test. Gas boiler is working fine at time of service.

Performed precision a/c tune up on Amana a/c system. Replaced Apriaire 413 air filter. ( provided by homeowner) checked all electrical connections and components. Found no surge protection on ecm blower motor, provided estimate. Checked temperature split. Checked refrigerant pressures and temperatures at indoor and outdoor unit. System is working fine at time of service.

Checked the a/c side of the system. Checked the air filter and replaced. Inspected the wiring connections and the voltages. Inspected the indoor coil and flushed and tested the coil pan and the condensate drain. Checked the blower motor condition and checked static pressure and amp draws . Checked the outdoor unit pressures by using super heat and sub cool methods. Inspected the capacitor and checked the amperage for the fan motor and the compressor. Checked the indoor cooling splits at the return and the supply. The a/c system is working fine at this time of service.

Replaced filter, inspected furnace and coils, blew out drain, checked electrical, checked delta t, checked capacitors, checked pressures. Blower motor was noisy on start up from water but the sound went away. Blower cap is starting to fail at 14.1/15. Unit is in normal operation at this time.

Performed precision a/c tune up on carrier package gas/a/c system. Found very dirty 2” by 16x16” air filters, picked up a distributer and replaced 4 air filters. Checked all electrical conections and components. Tested blower capacitor. Examined coils. Checked refrigerant pressures and temperatures . Main a/c is working fine. Smaller package gasa/c system is still down since 5he last visit. No point in performing a tune up on this system.

Performed precision a/c tune up on (2) amana a/c systems. Replaced (1) 14x24x1 air filter and (1) 16x20x1 air filter. Checked all electrical conections and components. Checked temperature split. Tested condensation drain with water. Checked refrigerant pressures and temperatures at indoor and outdoor units. Both systems are working fine at time of inspection.

Completed (2) Plan Member AC tune ups. Attic system filter (16x25x1) Ok Replaced basement system filter 20x25x4 with a 20x25x1 filter For BOTH systems: Inspected condition of both the indoor and outdoor coil Measured temperature split and static pressure Ensured drains were clear. Attic system has EZ trap and wet switch installed. Basement system has only the condensate pump safety as an after safety. Left previously quoted estimate for wet switch for basement system. Inspected wiring, controls, electric motors and components. Verified integrity of compressor motors using megaohmeter. Monitored R410A refrigerant pressures and diagnostics. Both system running at manufacturers target Subcooling. Homeowner wants to renew (2) plan memberships today. Asked that the office call to collect payment. He was busy with work.

Completed $200 assessment, received check, and took measurements to prepare proposal. Recommend follow up HVAC visit to assess ductwork in attic, as well as duct design and sizing for currently unfinished basement that will likely be finished later this year.

Arrived on site to complete heat tune up on gas furnace, inspected all electrical connections and wiring, inspected air filter, replaced humidifier pad and set for winter application inspected venting and ductwork, cleaned out flue trap and condensate pump, collected temperature splits from return and supply and confirmed proper temperature rise, cleaned all burners and flame sensor, inspected hsi, tested and flushed all drain lines, tested thermostat operations, confirmed good inlet and ouput gas pressures, completed combustion test and allowed system to cycle through setpoint, all system operations normal.…

Found gas furnace locking out on a limit open code with no limits open checked limits with a meter. Circuit board has failed. Package gas a/c has 2 boards in the system would recommend replacement of both board. Will need to get a price from the distributer on circuit boards. Other option is to replace the package gas a/c. Will get quote on replacement parts.

Completed Oil Boiler Tune up for Williamson boiler 147,000 BTUs Inspected and cleaned flues as heat exchanger. Checked hydronic ad oil piping and fitting for leaks. Checked all hydronic piping components: circulator, super vent, compression tank. Replaced GarBer spin on oil filter replaced 1.25 80B Nozzle Inspected all aspects of burner: Electrodes in good condition, verified proper orientation; Verified pump pressure (100psi) and cut off Checked Hydrostat settings; monitored boiler temperature and pressure during tune up procedures Combustion, draft and smoke tests: Pass Oil boiler is operating well at the time of this tune up.

Arrived to perform heating maintenance on gas furnace, called for heating at thermostat. System kicked on, performed combustion test, checked gas line for leaks, inspected duct work, checked temp rise, checked filter and changed filter. Checked drain, checked pressure switches, inspected inducer motor, checked capacitor on blower, inspected blower compartment, checked ad tested flame sensor and inspected igniter, tested and checked gas valve and pressure, inspected burner assembly and check and tested heat exchanger, system is running at the time of service. Capacitor on blower is reading weak. Informed customer and offered to change on site, customer would like to see it through until next maintenance.

Found boiler running upon arrival. Customer complaint was back rooms not getting hot, current boiler is single pipe hydronic, checked water piping all baseboard is getting hot. Those rooms are last of circuit. Also both rooms do not have sufficient baseboard. System is working fine.

Performed heat maintenance for 60KBTU natural gas furnace: Replaced 16x25x1 filter. Inspected heat exchanger, burners, ignitor, pressure switch and components. Checked wiring, controls, electric motors and components. Verified natural gas valve outlet pressure. Measured temperature rise and static pressure. Combustion/draft test: Good Furnace is operating well at the time of visit, provided an estimate to install air purifier

Arrived to perform 2 heating maintenance on gas furnaces, called for heating at thermostat. System kicked on, performed combustion test, checked gas line for leaks, inspected duct work, checked temp rise, checked filter and changed filter. Checked drain, checked pressure switches, inspected inducer motor, checked capacitor on blower, inspected blower compartment, checked ad tested flame sensor and inspected igniter, tested and checked gas valve and pressure, inspected burner assembly and check and tested heat exchanger, system is running at the time of service. 1st floor system in basement I highly recommend adding a wet switch to the system like the attic system to stop system from producing water if it were to detect water on ground, helping protect flooring in basement.